Vennligst vent...

Produktet ble lagt i handlekurven.Se handlevognen her
Handlekurven din er tom.
Tom handlevogn
Forsiden > AV SELVBYGG > AV-ROM BYGGEVARER > Lydisolering > DreamScreen ProSilence Clip for Wall and Ceiling Detachment

Vennligst vent...

ProSilence Clip for Wall and Ceiling Detachment
SKU: ProSilence_Clip
Kjøp 1 stk til: 49,-
Kjøp 100 stk til: 45,-
På lager På lager I butikk På fjernlager 10+ stk tilgængelig produkt(er) på lager til angitt spesialpris.
Antall:

49,-
 
Beskrivelse

 

Nyhet fra DreamScreen! Avkoblingsclips for tak og vegger som kun bygger 2,5cm ut og er totalt avkoblet med gummi i motsetning til de fleste øvrige clips som kobler selve stålstenderen mot clippen med stål. Dette kan i noen tilfeller føre til klirrelyder i visse frekvenser, noe en unngår risikoen for ved bruk av disse spesialdesignede clipsene. Husk å kjøpe de tilpassede stålstendrene (se under tilbehør) og vi anbefaler også DreamScreens egne spesialtilpassede selvborrende stålskruer (også under tilbehør).

Beregning av nødvendig innkjøpsvolum til ditt rom får du hjelp til lenger ned på siden her!

 

Informasjon fra produsent

 

If you are looking for the best possible reduction of noise generated from your cinema room, recording studio or similar type of room there is simply no way around decoupling the floor, walls and ceiling. If you decouple, the sound is unable to travel as easily through the construction, reducing both high -and low frequency noise very effeciently.

Please note that in addition to decoupling the walls, ceiling and floor using our clips and U-boats you need to install a sound resistant door (or even two doors for maximum reduction of noise) as well as plan for ventilating the room as it will be 100% airtight. Please consult your local dealer for further advice.

When reducing the noise generated inside a room, there are three major things you can do to further improve the effect of the decoupling:

1. Add mass, such as adding a second layers of plasterboard
2. Add air, such as a deeper stud
3. Add insulation (if not already present) 

The DreamScreen ProSilence Clips are extremely effecient in reducing the noise emitted from a room by using physical decoupling. The steel stud is decoupled without leaving any metal vs metal connections common on other clips (stud is totally covered in rubber) that potentially could make audible resonance at certain frequencies.

The clips are easy to install, and are suited for both ceiling -and wall installations. When installing the clips, please do not use more than two leafs, avoiding the so-called "Triple leaf effect", reducing the effect of the decoupling significantly. This applies also to four, five or any given number of leafs in excess of two. The Green Glue Company has made out an excellent guide in terms of explaining the issue of the Triple Leaf Effect here >>.

Please be noted that a massive concrete wall also is to be considered as one "leaf" and adding studs + clips + plasterboard on the inside room would functions in the same manner as the example above.

These illustrations displays the use of the DreamScreen ProSilence Clips in the ceiling and wall as well as the DreamScreen ProSilence U-Boats in the flooring for extremely effective decoupling. On the other side of the studs, both in the ceiling and walls, we recommend you use only one compact layer / leaf, however this layer / leaf may consist of several bonded panels of gipsum or consist of massive (light) concrete.

After you have installed the clips and attached the metal studs, we recommend using two layers of plasterboard, preferably with a vicoustic compound such as Green Glue in between. Also, please make sure you leave about 2mm opening on the top and bottom and seal this off with acoustical sealant.

 

 


The system will require only 25mm of space before applying the plasterboard.


You need about 3 clips per square meter wall- or ceiling, and half that figure in 2m studs (i.e. 1,5 stud per sqm), please see the form below for calculating your estimated requirement.
 

Calculating the required quantitiy of clips and steel studs


As you can see from the above chart, for a room that measures 5m x 4m x 2,5m you would need to purchase:
 
 
Wall 1 + 2: 5m x 2,5m = 12,5m2 x 2 = 25m2
Wall 3 + 4: 4m x 2,5m = 10m2 x 2 = 20m2
Ceiling: 5m x 4m = 20m2
 
 
 
Total # square meter: 75m2, which would require about 167 clips and 167/2=84 studs. It would always be a good idea to add some clips and studs in case you need to do some small adjustment.
 
 
 
INSTALLATION
 
 
 
 


The clips and studs can be used both in ceilings and on walls
 
 
 
 
 
 
 
 
 

1. First, you attach the metal section of the clip to the wall or ceiling.

2. Then widen both ends of the metal clip a little so that the rubber will fit more easily.

3. All the required rubber sections should be slided in to the stud prior to attaching it.
 
4. Last, to secure the rubber to the metal clip, please use a hammer on each side.
 
5. Then you connect new studs and follow the same procedure. Please use about 10cm and four screws for each connection.

 

 

Selv om vi gjør vårt beste for å gi relevant informasjon, så er bildene kun for å gi et generelt inntrykk, og selve varen er ikke nødvendigvis akkurat slik som avbildet. Dersom det er forskjeller mellom produktoverskrift, beskrivelse og bilde, så er det produktoverskriften som gjelder (f.eks. PCer kommer ikke nødvendigvis med skjerm selv om bildet viser det). Hvis noe er uklart, vennligst send epost til kundestøtte før du bestiller. Vi tar forbehold om trykkfeil og endring av priser og spesifikasjoner uten varsel.